OK, Here we made a User Manual about Lonsdor K518ISE BMW CAS2/CAS3 for you ,hope it helps!
Immobilizer - BMW - select from type - CAS2/CAS3
Function
1. Immobilizer: program keys
2. Use eeprom data to generate a new key:
Backup eeprom data to generate a dealer key
3. Enable key: Program and activate the key disabled
Disable key: Program and disabled keys available or lost
4. Backup and recover:
Backup the key data and remove it if necessary
5. Update CAS3: Immobilizer will be identified if the system can be programmed or not.
If not, it will ask you to update CAS3. please wait for another 10 min and return to the the “Immobilizer” menu to operate.
6. Compel to recover CAS3: Force to recover CAS3, if CAS3 update goes wrong
7. Sync DME: Please Sync DME if the car fails to start after programming keys
8. Sync ELV: Please Sync ELV if the car fails to start after programming keys
9. Clear fault codes: Clear fault message the vehicle produced
1. Immobilizer: program keys
2. Use eeprom data to generate a new key:
Backup eeprom data to generate a dealer key
3. Enable key: Program and activate the key disabled
Disable key: Program and disabled keys available or lost
4. Backup and recover:
Backup the key data and remove it if necessary
5. Update CAS3: Immobilizer will be identified if the system can be programmed or not.
If not, it will ask you to update CAS3. please wait for another 10 min and return to the the “Immobilizer” menu to operate.
6. Compel to recover CAS3: Force to recover CAS3, if CAS3 update goes wrong
7. Sync DME: Please Sync DME if the car fails to start after programming keys
8. Sync ELV: Please Sync ELV if the car fails to start after programming keys
9. Clear fault codes: Clear fault message the vehicle produced
Operation
CAS2/CAS3: Backup and recover (backup the key data) - eeprom data to generate keys (pls select OBD to generate) - program key
CAS3+/CAS3++: Backup and recover (backup the key data) - dismantle the CAS immo box and read its data and backup eeprom data with the programmer - eeprom data to generate a key (pls select OBD to generate) - program key
Note:
1. CAS2/CAS3: the operations to add keys and all keys lost are the same
CAS3+: all keys lost need to dismantle the body ECU
CAS3++: all keys lost operation is not supported
2. Keys with the bar type is not supported currently
3. CAS case (box) is under dashboard generally
CAS2/CAS3: Backup and recover (backup the key data) - eeprom data to generate keys (pls select OBD to generate) - program key
CAS3+/CAS3++: Backup and recover (backup the key data) - dismantle the CAS immo box and read its data and backup eeprom data with the programmer - eeprom data to generate a key (pls select OBD to generate) - program key
Note:
1. CAS2/CAS3: the operations to add keys and all keys lost are the same
CAS3+: all keys lost need to dismantle the body ECU
CAS3++: all keys lost operation is not supported
2. Keys with the bar type is not supported currently
3. CAS case (box) is under dashboard generally
Attention
1. Suggestion to backup the key data before all operation
2. For CAS3, CAS3+, CAS3++systems, you can program 2 smart keys at most. To program smart keys, you need to disable one smart key first, then program a new key
3. It will take 10 min to update CAS. Pls make sure the auto batteries are fully charged
Note: don’t use this function when the voltage is less than 1.5v. pls charge the battery and make sure the voltage is more than 11.5v. during the update, neither cut off the power nor insert the key. For smart keys, pls take it outside the vehicle
4. For CAS3+ all keys lost, you mast dismantle and read backup data. Use the data to make a dealer key and then program the car keys. For CAS3++, you can add a new key to it but there is no possible solutions to all keys lost.
5. This system can be operated via OBD. But to reduce risk of immobilizer, you are advised to backup secure data of the body ECU with the programmer for CAS3+, CAS3++ systems. When the programming fails, the data can be recovered and back to the initial state
6. If the key can’t start the car after programming is completed, please try to sync DME and ELV
Reference
PIN code: PIN code requirement
Remote generation: When key programming completes, the remote control will be generated automatically
OBD location: Under the steering wheel (close to pillar A)
Lonsdor K518 BMW Immobilizer system:
CAS1:
7 series 2001-2005
CAS2:
3 series 2005-2007
5 series 2004-2007
6 series 2003-2008
7 series 2005-2009
CAS3:
1 series 2007-1008
3 series 2007-2008
5 series 2008-2010 (some CAS3+)
6 series 2008-2010 (some CAS3+)
Z4 after 2008 (some CAS3+)
CAS3+:
1 series 2009-2012
3 series 2009-2012
5 series 2008-2010 (some CAS3)
6 series 2008-2010 (some CAS3)
X1 before 2014
X5 2008-2013
Z4 after 2008 (some CAS3)
MINI 2008-2014 46 chip
CAS4:
5 series 2010-2012
6 series 2010-2012
7 series 2010-2012
X3 after 2012 (some CAS4+)
X4 after 2013 (some CAS4+)
CAS4+:
5 series after 2012
6 series after 2012
7 series after 2012
X3 after 2012 (some CAS4)
X4 after 2013 (some CAS4)
EWS3:
3 series before 2005 73 or 44 chip (other 3 series is the 46 chip)
5 series before 2004 No 18
Z4 before 2008
X5 before 207 (some EWS4)
Ews4:
X3 before 2011
X5 before 2007 (some EWS3)
Lonsdor K518 BMW Chip types:
46 chip (incl common 46 chips):
1 series 2007-2012
3 series 2005-2012
5 series 2004-2010
6 series 2003-2010
7 series 2001-2009
X1 before 2014
X5 before 2013
73 or 44 chip:
3 series before 2005
5 series before 2004
X3 before 2011
X5 before 2007
Z4 before 2008
MINI 2008-2014
Specific smart keys:
5 series after 2010
6 series after 2010
7 series after 2010
X3 after 2012
X4 after 2013
Hi,
ReplyDeleteHi,
ReplyDeleteLonsdor K518ise can make all key lost bmw x1 2017