How to update Lonsdor K518ISE Hibernation Function?

Updated Device: Lonsdor K518
Updated Condition: for all K518 devices with working normally
Updated Content: Added Hibernation function; Kernel update supported
Updated Version: K518 APK V1.5.25

Preparation for Update:

1. Power on the device or keep the battery level over 80%.
2. Make sure wifi network is in good condition and the device receives signal normally;

Update steps:

1. Click [One key update] and skip to below interface. Then click the first button to update system. When the update complete, click [OK] to reboot the device.

2. After rebooting, click and enter [Settings] menu, you will find there are two additional function buttons: [Update Kernel ] and [Display Settings].

3. Click [Update Kernel] first and skip to below interface, then press [Update] to update the kernel.

4. Click [Install] after updating the kernel file. And the device will reboot to install kernel.

5. Blank screen is normal during the installation. The whole process will take 5 minutes, be patient to wait and don’t restart the device manually.

6. The update complete when the password input interface appears. Screen auto-lock in the [Display Settings ] is added.

7. Enter [Settings]→[Display Settings] to adjust the screen brightness and screen auto-locking time .

8. The benefits for update: Save power to prolong stand-by time. Auto standby function can prevent the device from being overheated in hot summer.

http://blog.obdexpress.co.uk/2018/04/15/how-to-update-lonsdor-k518ise-hibernation-function/

How to Use Lonsdor K518 Hex editor

User manual：Lonsdor K518 Hex editor Instructions

1 Open Hex editor

• Enter K518 home screen, select【settings】

• In【settings】menu, select【Hex editor】

• 【Hex editor】interface as shown 

Back to home screen    Back to previous menu

2 Open file

【Hex editor】interface: You can only click【Open file】 and 【Calculator】. Other grey buttons are unclickable when no file is read.

• Please open file first before further operations. Click 【Open file】and select right path to store the file.

customfile：Store user temporary data
file：Store APP data

Select a bin file, opened as a Hex file

3 Search data

• Click【Search data】, and prompt “Please input data to be searched”. Then input the data and click【Search】. Default values is on where the cursor is in below pic.

• Small keypad:

Click number to input data.
Click “←” to delete data.
Click “close” to close the keypad.

• Stop searching data: Please click【Cancel】.
• Start to search data: please click【Search】, and the cursor will skip to corresponding data as shown below.

For example: If you input No. 12, and click【Search】. The data you’re searching is highlighted as shown below.

• After searching the data,【Search previous】and【Search next】buttons will turn to blue and clickable. Click【Search previous】or【Search next】, and you will find previous or next same data.

4 Edit data

• Revise a Hex number: Please search and find the number. Then click【Edit data】to revise it. For example, click to edit data when you find No. 12 (see below pic).

If you want to change the number to A9, please input A9 on small keypad directly. Then all the number will change to “A9” synchronously.

5

Save file

• How to save revised data: Click【Save file】to input filename and click【Save】.

• You can also return to home screen and select “not save”. The revised data will not be saved in this case. Click【Save file】as shown below.

• The filename defaults to be the one when it’s open. If you need to revise the filename, click the prompt frame and input new filename and click 【Save】. Refer to below pic.

6 Calculator

【Calculator】includes two functions: SysConvert and XOR.

• SysConvert: Arbitrary conversion among Hex, Bin, Dec and Oct.

Click any number on the screen, and the number will be converted automatically. For example, click “94”, the calculator will convert it to Bin, Dec and Oct numbers. Refer to below pics.

Prompt frame can be moved around the screen.

You can also input data to convert it with small keypad, as shown below.

• For XOR, you need to input No.1 and 2 manually. The calculating result is as follows:

http://blog.obdexpress.co.uk/2018/04/13/lonsdor-k518-hex-editor/

Ｈow to use Lonsdor Toyota/Lexus smart key To Do ALL Key Lost

1.Toyota Lexus – Smart key – All key lost – Helps

Applied to ：Toyota/Lexus the 5th emulator for Chip 39 (128 bit)
&“94/D4”–the Black

This help file basically includes 4 parts: Function, Operation, Attention, and

Reference.

Functions

Operational process for all key lost

Please confirm whether emulator key (SKE) is bound to K518 device beforehand.

Backup EEPROM data-> Generate new data-> Dismantle immo box and write

new data to EEPROM-> Generate SKE-> Add/delete smart key

1. Backup original EEPROM immo data.
2. Use backup data to generate new data.
3. System certify and generate new data automatically, and program SKE to

become an available key,which can open dashboard.,before key programming.

4. Add a smart key.
5. Delete programmed key.
6. Bind SKE: Require to bind all SKE to K518 for the first use.

Operation

Operational process for all key lost

Please confirm whether K518 is bound to emulator key (SKE).

1. Backup EEPROM data–> 2. Generate emulator key (SKE)–> 3. Use SKE to

switch ignition ON–> 4. Add smart key

Operation

1. Backup EEPROM immo data.
2. Generate a SKE for emergency use.
3. Put the SKE close to start button and dashboard will be lit up.
4. Add a smart key.
5. Delete a smart key.

Bind emulator key

1. This function can bind emulator key (SKE-LT series) to K518 host.
2. Please insert key to be bound into the host slot.
3. System is binding… Program key when key binding complete.

Backup EEPROM data

1. This function can backup EEPROM data.

Generate SKE for emergency when data backup complete.

Insert SKE to switch ignition ON and open dashboard.

2. Receiving vehicle immo data… Please wait patiently.
3. Please name EEPROM backup data.
4. Data backup succeed.Please select “generate emulator key”function to generate a spare key for emergency.

Generate emulator key

1. This function can generate a spare master key when all keys are lost, which can

open dashboard to add other keys.

2. Receiving local backup data…
3. System shows current data and notify key type.
4. Insert bound emulator key (corresponding color/type) into K518 host slot, and press

round button on the key.

5. Generating SKE … Please wait for 5 minutes patiently.
6. When SKE is generated,press round button on it and put it against start button of

vehicle, and try to open dashboard.If the dashboard is lit up, please use SKE to

program and add new keys.

Add smart key

1. Put SKE or available key against ignition switch and switch ignition ON till

dashboard is lit up.

2. System communication, getting info about key numbers…
3. Put registered smart key against vehicle start button, and remove it when

buzzer beeps once.

4. Put smart key (to be registered) at start button of vehicle in 30 seconds, and

remove it when buzzer beeps twice.

5. Please wait till key registration complete. Operation succeed.

Delete smart key

1. Put emulator key or available key close to ignition switch and switch ignition ON till

dashboard is lit up.

2. System communication, getting info about key numbers…
3. Put back of registered smart key close to vehicle start button, and remove it

when buzzer beeps once.

4. System is deleting key… Deleting succeed. Smart key (away from start button) will be deleted.

Attentions

1. Bind emulator key: Require to power on the device when put emulator key into

K518 host slot.

2. System will read backup data of vehicle to generate emulator key and prompt

to choose corresponding key type(refer to back of the emulator).

4.For Carola/Vios/Zelas all key lost, programming is not available in a state of alarm.

2.Toyota Lexus – Smart key – All key lost – Helps With LOND

Applied to ：Green 98 SKE-LT Smart Key Emulator

This help file basically includes 4 parts: Function, Operation, Attention, and

Reference.

Functions

Operational process for all key lost

Please confirm whether emulator key (SKE) is bound to K518 device beforehand.

Backup EEPROM data-> Generate new data-> Dismantle immo box and write

new data to EEPROM-> Generate SKE-> Add/delete smart key

1. Backup original EEPROM immo data.
2. Use backup data to generate new data.
3. System certify and generate new data automatically, and program SKE to become an available key, which can open dashboard, before key programming.
4. Add a smart key.
5. Delete programmed key.
6. Bind emulator key: Require to bind all SKE to K518 for the first use.

Operation

Operational process for all key lost

Please confirm whether K518 is bound to emulator key (SKE).

Backup EEPROM immo data-> Generate new data-> Dismantle immo box and

write new data to EEPROM-> Generate SKE-> Add/delete smart key

Backup EEPROM data

1. This function can backup EEPROM data.
2. System is receiving data, please wait patiently.
3. Please input data filename and save succeed.
4. EEPROM data backup complete, please select “generate EEPEOM data”

function to generate specific data.

Generate EEPROM data

1. This function can generate EEPROM data for vehicle.
2. Continue to select EEPROM data of smart key backed up before.
3. Searching data… Please input filename of new data.
4. Generating EEPROM data complete. Data saved in K518\file\feature_1013.

Please write newly-generated data to EEPROM（IC003）in smart immo box of

vehicle. More details, refer to “Reference”.

89990-0N010 smart immo box (see below pic)

89990-06060smart box(see below pic)

Note: Install back smart box when data writing complete.

Generate emulator key

It’s required to write newly-generated data to EEPROM in smart immo box.

Dashboard is lit up after emulator key (SKE) generated.

1. This function can generate a backup master key when all keys are lost, which

can open dashboard to add keys.

2. Insert bound SKE(corresponding color/type) into K518 card slot, and press

round button on the key.

3. System is building configuration… Please wait patiently.
4. Key generation complete. Please press round button on it and put it against

ignition switch of vehicle, and try to open dashboard. If the dashboard is lit up,

please use SKE to program and add new keys.

Add smart key

1. Put emulator key or available key against ignition switch and switch ignition ON

till dashboard is lit up.

2. System communication, getting info about key numbers…
3. Put registered smart key against start button of vehicle, and remove it when

buzzer beeps once.

4. Please put smart key to be registered at start button of vehicle in 30 seconds,

and remove it when buzzer beeps twice.

5. Please wait till key registration complete. Operation succeed.

Delete smart key

1. Put emulator key or available key close to ignition switch and switch ignition

ON till dashboard is lit up.

2. System communication, getting key numbers…
3. Put back of registered smart key close to vehicle start button, and remove it

when buzzer beeps once.

5. System is deleting key… Deleting succeed. Smart key (away from start button)

will be deleted.

Bind emulator key

1. This function can bind smart key emulator (SKE-LT series) to K518 host.
2. Please put key to be bound into K518 host slot.
3. System is binding… When complete, continue to program all keys lost.

Attentions

1. Newly-generated data must be written to EEPROM chip in smart box.

Dashboard can be lit up after simulate key is generated.

2. Bind key/generate key: Change placement of simulate key to sense if failed.

98 card smart box is located at back of storage box at passenger seat.

Reference

Chip type	94/D4(SKE black), 88/A8(SKE red), A9(SKE blue), 39(SKE orange)
Remote control type	Specific smart key
Key embryo No.	Specific smart key
Password required or not	Not required.
Remote control	Generate automatically when smart key programming complete.
OBD position	Under steering wheel
Reference pics	Smart key appearance for part of Toyota series     Toyota series： 2008  Reiz 0111   smart key 2008  RAV4 0111  smart key 2008  Prado 0140 smart key 2008  Camry 0140 smart key 2008  Corolla 0111 smart key 2008  Cruiser A433 smart key 2008  Alfa      smart key 2008  Previa     smart key 2008  Lexus 0140  smart key 2010  Camry 3370  smart key 2010  Prado 3370  smart key 2010  Reiz 5290  smart key 2010  Crown 5290 smart key 2010  Lexus 3370  smart key 2010  Camry 0020 smart key 2012  Reiz 7930   smart key 2012  Crown 7930 smart ky 2012  Prado 7930  smart key 2012  RAV4 7980  smart key 2013  Lexus ES GS IS  smart key 2014  RAV4    2-button smart key 2014  RAV4    3- button smart key 2014  New vios/Yaris L   smart key Lexus smart key，select from PCB type： 89904-30291（0140 PCB  ES350 old ver. ) 89904-50430（3370 PCB  ES240/ES350 new ver.） 89904-48321  (5290 PCB  PX270） 89904-28132（0780 PCB  5-button Previa） 89904-6071 （A433 PCB  Cruiser） 89904-0041(0111PCB RAV4 3-button Reiz Carola)

Source:http://www.obdexpress.co.uk/wholesale/ske-lt-smart-key-emulator-lonsdor-k518ise-ograge.html

Price: 185USD(150EURO) not incl. shipping cost.